SignsBot

Код
Документация на английском и немецком

Из инструментов есть робот, управляемый программой, записанной на знаках. Робот требует электропитания, и поэтому работает в комплексе с модом Techage. Также есть датчики и таймер.

Программа управления роботом пишется на своём несложном языке управления, чем-то похожем на язык Turtle/Черепашка

Основные команды:
move <steps>	go one or more steps forward
cond_move	go to the nearest obstacle or sign
turn_left	turn left
turn_right - turn right
turn_around - turn around
backward - take a step back
turn_off - turn off the robot / back to the box
pause <sec> - wait one or more seconds
move_up - move up (maximum 2 times)
move_down - move down
fall_down - fall into a hole/chasm (up to 10 blocks)
take_item <num> <slot> - take one or more items from a box
add_item <num> <slot> - put one or more items in a box
add_fuel <num> <slot> - put fuel in a furnace
place_front <slot> <lvl> - place the block in front of the bot
place_left <slot> <lvl> - place the block to the left of the bot
place_right <slot> <lvl> - place the block to the right of the bot
place_below <slot> - lift the robot and put the block under the robot
place_above <slot> - set block above the robot
dig_front <slot> <lvl> - remove block in front of the robot
dig_left <slot> <lvl> - remove block on the left
dig_right <slot> <lvl> - remove block on the right
dig_below <slot> - remove block under the robot
dig_above <slot> - remove block above the robot
rotate_item <lvl> <steps> - rotate a block in front of the robot
set_param2 <lvl> <param2> - set param2 of the block in front of the robot
place_sign <slot> - set sign
place_sign_behind <slot> - put a sign behind the bot
dig_sign <slot> - remove the sign
trash_sign <slot> - Remove the sign, clear data and add to the item Inventory
stop - Bot stops until the shield is removed
pickup_items <slot> - pickup items (in a 3x3 field)
drop_items <num> <slot> - drop items
harvest - harvest a 3x3 field (farming)
cutting - cut flowers in a 3x3 field
sow_seed <slot> - see/plant a 3x3 field
plant_sapling <slot> - plant a sapling in front of the robot pattern - save the block properties behind the sign (3x3x3 cube) as a template
copy <size> - make a 3x3x3 copy of the stored template
punch_cart - bump a mine cart
add_compost <slot> - Put 2 leaves into the compost barrel
take_compost <slot> - Take a compost item from the barrel
print <text> - Output chat message for debug purposes
take_water <slot> - Take water with empty bucket
fill_cauldron <slot> - Fill the xdecor cauldron for a soup
take_soup <slot> - Take boiling soup into empty bowl from cauldron
flame_on - Make fire
flame_off - Put out the fire

Взаимодействие с Techage:
ignite - Ignite the techage charcoal lighter
low_batt <percent> - Turn the bot off if the battery power is below the given value in percent (1..99)
jump_low_batt <percent> <label> - Jump to <label> if the battery power is below the given value in percent (1..99) (see "Flow control commands")
send_cmnd <receiver> <command> - Send a techage command to a given node. Receiver is addressed by the techage node number. For commands with two or more words, use the '' character instead of spaces, e.g.: send_cmnd 3465 pulldefault:dirt*2

Управление порядком исполнения:
jump <label> -- jump command, <label> is a word from the characters a-z or A-Z
<label>: -- jump label / start of a function
return -- return from a function
repeat <num> -- start of a loop block, <num> is a number 1..999
end -- end of a loop block
call <label> -- call of a function (with return via the command 'return')
jump_check_item <num> <slot> <label> -- Check if there are <num> items in the chest like node. -- If not, jump to <label>. -- <slot> is the bot inventory slot (1..8) to -- specify the item, or 0 for any item.
jump_low_batt <percent> <label> -- See "Techage specific commands"