SignsBot
- Код
- Документация на английском и немецком
Из инструментов есть робот 
signs_bot:box, управляемый программой, записанной на знаках 
signs_bot:sign_cmnd. Робот требует электропитания, и поэтому работает в комплексе с модом Techage. Также есть датчики и таймер.
Программа управления роботом пишется на своём несложном языке управления, чем-то похожем на язык Turtle/Черепашка
| Основные команды: | |
| move <steps> | один или <steps> шагов вперёд |
| cond_move | go to the nearest obstacle or sign |
| turn_left | повернуться влево |
| turn_right | повернуться вправо |
| turn_around | развернуться |
| backward | шаг назад |
| turn_off | выключение и возврат робота в бокс |
| pause <sec> | одижать одну или <sec> секунд |
| move_up | подняться вверх (максимум 2 раза) |
| move_down | опустится вниз |
| fall_down | fall into a hole/chasm (up to 10 blocks) |
| take_item <num> <slot> | взять <num> объектов из слота номер <slot> из ящика |
| add_item <num> <slot> | put one or more items in a box |
| add_fuel <num> <slot> | put fuel in a furnace |
| place_front <slot> <lvl> | place the block in front of the bot |
| place_left <slot> <lvl> | place the block to the left of the bot |
| place_right <slot> <lvl> | place the block to the right of the bot |
| place_below <slot> | lift the robot and put the block under the robot |
| place_above <slot> | set block above the robot |
| dig_front <slot> <lvl> | remove block in front of the robot |
| dig_left <slot> <lvl> | remove block on the left |
| dig_right <slot> <lvl> | remove block on the right |
| dig_below <slot> | remove block under the robot |
| dig_above <slot> | remove block above the robot |
| rotate_item <lvl> <steps> | rotate a block in front of the robot |
| set_param2 <lvl> <param2> | set param2 of the block in front of the robot |
| place_sign <slot> | set sign |
| place_sign_behind <slot> | put a sign behind the bot |
| dig_sign <slot> | remove the sign |
| trash_sign <slot> | Remove the sign, clear data and add to the item Inventory |
| stop | Bot stops until the shield is removed |
| pickup_items <slot> | pickup items (in a 3x3 field) |
| drop_items <num> <slot> | drop items |
| harvest | harvest a 3x3 field (farming) |
| cutting | cut flowers in a 3x3 field |
| sow_seed <slot> | see/plant a 3x3 field |
| plant_sapling <slot> | plant a sapling in front of the robot |
| pattern | save the block properties behind the sign (3x3x3 cube) as a template |
| copy <size> | make a 3x3x3 copy of the stored template |
| punch_cart | bump a mine cart |
| add_compost <slot> | Put 2 leaves into the compost barrel |
| take_compost <slot> | Take a compost item from the barrel |
| print <text> | Output chat message for debug purposes |
| take_water <slot> | Take water with empty bucket |
| fill_cauldron <slot> | Fill the xdecor cauldron for a soup |
| take_soup <slot> | Take boiling soup into empty bowl from cauldron |
| flame_on | Make fire |
| flame_off | Put out the fire |
| Взаимодействие с Techage: | |
| ignite | Ignite the techage charcoal lighter |
| low_batt <percent> | Turn the bot off if the battery power is below the given value in percent (1..99) |
| jump_low_batt <percent> <label> | Jump to <label> if the battery power is below the given value in percent (1..99) (see "Flow control commands") |
| send_cmnd <receiver> <command> | Send a techage command to a given node. Receiver is addressed by the techage node number. For commands with two or more words, use the '*' character instead of spaces, e.g.:
send_cmnd 3465 pull*default:dirt*2 |
| Управление порядком исполнения: | |
| jump <label> | jump command, <label> is a word from the characters a-z or A-Z |
| <label>: | jump label / start of a function |
| return | return from a function |
| repeat <num> | start of a loop block, <num> is a number 1..999 |
| end | end of a loop block |
| call <label> | call of a function (with return via the command 'return') |
| jump_check_item <num> <slot> <label> | Check if there are <num> items in the chest like node.
-- If not, jump to <label>. -- <slot> is the bot inventory slot (1..8) to -- specify the item, or 0 for any item. |
| jump_low_batt <percent> <label> | See "Techage specific commands" |